[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"$fS5CDRsy3cdBAyTXxB8Qxi3muStDctHSE4nII5T9_6lc":3},{"answer":4,"createTime":5,"id":6,"options":7,"origin":12,"question":16,"related":17,"source":21,"type":22},[],"2024-01-02 17:02:07",125653976,[8,9,10,11],"由于电表存在零点读数而产生的误差","由于实验环境或操作条件的的微小波动所引起的误差","由于实验者在判断和估计读数上的变动性而产生的误差","由于实验测量对象的自身涨落引起的测量误差",{"courseId":13,"courseImg":14,"courseName":15},"1a09b2ed6eca3649a196922341a54531","https:\u002F\u002Ftihai-oss-cloud.itihey.com\u002Fimg\u002Fde8fc126ff04ca1915faed43b417c431.jpg","大学物理实验","测量误差可分为系统误差和偶然误差,属于系统误差的有: ( )",[18,23,32,41,50,60,69,74,83,92],{"answer":19,"createTime":5,"id":6,"options":20,"question":16,"source":21,"type":22},[],[8,9,10,11],"v1",0,{"answer":24,"createTime":5,"id":25,"options":26,"question":31,"source":21,"type":22},[],125653978,[27,28,29,30],"系统误差可以通过多次测量消除","偶然误差一定能够完全消除","记错数是系统误差","系统误差是可以减少甚至消除的","下面说法正确的是: ( )",{"answer":33,"createTime":5,"id":34,"options":35,"question":40,"source":21,"type":22},[],125653979,[36,37,38,39],"一般来说,测量结果的有效数字多少与测量结果的准确度无关","可用仪器最小分值度或最小分度值的一半作为该仪器的单次测量误差","直接测量一个直径约1 mm 的钢球,要求测量结果的相对误差不超过5%,应选用最小分度为1mm 的米尺来测量","实验结果应尽可能保留多的运算位数,以表示测量结果的精确度","下列哪种说法是正确的: ( )",{"answer":42,"createTime":5,"id":43,"options":44,"question":49,"source":21,"type":22},[],125653981,[45,46,47,48],"0.05136","0.0514","0.051","0.1","两个直接测量值为0.5136mm和10.0mm,它们的商是( )",{"answer":51,"createTime":52,"id":53,"options":54,"question":59,"source":21,"type":22},[],"2024-01-02 17:02:08",125653983,[55,56,57,58],"真值","最接近真值的值","误差最大的值","误差为零的值","对一物理量进行等精度多次测量,其算术平均值是:( )",{"answer":61,"createTime":52,"id":62,"options":63,"question":68,"source":21,"type":22},[],125653985,[64,65,66,67],"534.3(mm)","534.2±0.5(mm)","534.3±0.5(mm)","534.27±0.5(mm)","如果多次测量的平均值为534.274毫米,不确定度为0.5毫米,测量结果应表示为( )",{"answer":70,"createTime":52,"id":71,"options":72,"question":73,"source":21,"type":22},[],125653986,[36,37,38,39],"下列哪种说法是正确的( )",{"answer":75,"createTime":52,"id":76,"options":77,"question":82,"source":21,"type":22},[],125653988,[78,79,80,81],"4.32749→4.328","4.32751→4.328","4.32750→4.328","4.32850→4.328","在计算数据时,当有效数字位数确定以后,应将多余的数字舍去.设计算结果的有效数字取4位,则下列不正确的取舍是:( )",{"answer":84,"createTime":52,"id":85,"options":86,"question":91,"source":21,"type":22},[],125653989,[87,88,89,90],"算术平均值","相对真值","理论值","某次测量值","被测量量的真值是一个理想概念,一般来说真值是不知道的(否则就不必进行测量了).为了对测量结果的误差进行估算,我们用约定真值来代替真值求误差.不能被视为真值的是:( )",{"answer":93,"createTime":52,"id":94,"options":95,"question":99,"source":21,"type":22},[],125653991,[8,96,97,98],"由于多次测量结果的随机性而产生的误差","由于量具没有调整到理想状态,如没有调到垂直而引起的测量误差","由于实验测量公式的近似而产生的误差","测量误差可分为系统误差和偶然误差,属于偶然误差的有"]