[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"$fWqFviSgjPpvUlwEtjk-w2__ZNmiNVwKCo63yasqoHAE":3},{"answer":4,"createTime":5,"id":6,"options":7,"origin":12,"question":16,"related":17,"source":27,"type":28},[],"2026-01-10 08:14:25",308357939,[8,9,10,11],"stm32f10x_rtc.h","stm32f10x_cec.h","stm32f10x_rcc.h","stm32f10x_bkp.h",{"courseId":13,"courseImg":14,"courseName":15},"54d7df879f1e91fb6fdac03359f7da0a","https:\u002F\u002Ftihai-oss-cloud.itihey.com\u002Fimg\u002F7aabb91502b766392cbe846c4020bd47.jpg","嵌入式应用技术","RTC库函数头文件是()",[18,29,38,47,56,65,74,83,86,95],{"answer":19,"createTime":5,"id":20,"options":21,"question":26,"source":27,"type":28},[],308357932,[22,23,24,25],"配置I2C为从模式并设置地址","配置I2C为主模式并设置地址","配置I2C为从模式并启用DMA","配置I2C为主模式并启用DMA","在STM32F103ZET6中,如何配置I2C为从模式","v1",0,{"answer":30,"createTime":5,"id":31,"options":32,"question":37,"source":27,"type":28},[],308357933,[33,34,35,36],"GPIO_ResetBits(GPIOA, GPIO_Pin_10 | GPIO_Pin_15)","GPIO_ResetBits(GPIOA, GPIO_Pin_8 | GPIO_Pin_9)","GPIO_ResetBits(GPIOA, GPIO_Pin_1 | GPIO_Pin_2)","GPIO_SetBits(GPIOA, GPIO_Pin_10 | GPIO_Pin_15)","将端口GPIOA的第10、15脚置0(低电平)的函数是()",{"answer":39,"createTime":5,"id":40,"options":41,"question":46,"source":27,"type":28},[],308357934,[42,43,44,45],"00H","08H","0CH","04H","端口输出数据寄存器的地址偏移为( )",{"answer":48,"createTime":5,"id":49,"options":50,"question":55,"source":27,"type":28},[],308357935,[51,52,53,54],"APB1 时钟","APB2 时钟","HSE","LSE","使用 TIM2 定时器生成 1s 中断时,以下哪个时钟源最常用",{"answer":57,"createTime":5,"id":58,"options":59,"question":64,"source":27,"type":28},[],308357936,[60,61,62,63],"配置DMA为外设到内存传输模式并启用中断","配置DMA为内存到外设传输模式并启用外设","配置DMA为外设到内存传输模式并启用外设和中断","配置DMA为内存到内存传输模式并禁用中断","在STM32F103ZET6中,如何启用DMA传输模式",{"answer":66,"createTime":5,"id":67,"options":68,"question":73,"source":27,"type":28},[],308357937,[69,70,71,72],"void RTC_WaitForLastTask(void)","void RTC_WaitForSynchro(void)","FlagStatus RTC_GetFlagStatus(uint16_t RTC_FLAG)","void RTC_ClearFlag(uint16_t RTC_FLAG)","清除RTC的待处理标志位的库函数是()",{"answer":75,"createTime":5,"id":76,"options":77,"question":82,"source":27,"type":28},[],308357938,[78,79,80,81],"OSTaskSetPriority()","OSTaskChangePriority()","OSTaskUpdatePriority()","无法动态调整任务优先级","在uCOS-III中,哪个函数用于实现任务的动态优先级调整",{"answer":84,"createTime":5,"id":6,"options":85,"question":16,"source":27,"type":28},[],[8,9,10,11],{"answer":87,"createTime":5,"id":88,"options":89,"question":94,"source":27,"type":28},[],308357940,[90,91,92,93],"加入滤波算法","提高电机频率","增加PWM占空比","使用高阻态GPIO","无人机避障过程中,STM32处理超声波传感器数据时,为了避免误触发,通常需要",{"answer":96,"createTime":5,"id":97,"options":98,"question":103,"source":27,"type":28},[],308357941,[99,100,101,102],"OSTaskGetStackPointer()","OSTaskStackPointer()","OSTaskQuery()","OSTaskStack()","在uCOS-III中,哪个函数用于获取一个任务的当前堆栈指针"]